Give your vape coil a longer lifespan and enjoy the ultimate vaping experience with these smart hacks!

Every vaper faces the dreaded burnt taste sooner or later, but this doesn’t have to be part of your story.

Welcome to a world where vape coils last longer, sessions are uninterrupted, and your budget smiles back at you. In this blog post, we dive right into five expert-appraised techniques aimed at preventing your vape coils from burning.

Conquer the art of maintenance, understand the science behind priming, and find out why less is actually more when it comes to power usage.

So buckle up as we explore how to make every puff count!

Priming A New Coil

When it comes to preventing vape coils from burning, one of the most important steps is properly priming a new coil. 

Priming involves saturating the cotton wicking material inside the coil with e-liquid before using it for the first time. This process ensures that the coil is well-saturated and ready to heat up effectively without any dry spots that could lead to burning.

Priming a new coil is a straightforward process that can significantly extend its lifespan. Start by removing the old coil from the tank and disposing of it properly.

Then, take your new coil and apply a few drops of e-liquid directly onto the cotton exposed through the wicking holes on the side of the coil. Make sure to apply enough liquid to thoroughly saturate the cotton but avoid over-saturating it, as this can also cause issues.

Tip: Patience is key when priming a new coil. Allow the e-liquid to soak into the cotton fully before using it. Wait for at least 5-10 minutes to ensure proper priming.

After allowing sufficient time for priming, you can reassemble your tank, refill it with e-liquid, and start vaping. By priming your new coil correctly, you create an optimal environment for smooth and flavorful vaping while minimizing the risk of burning.

Saturating Coils with E-Liquid

Once you have successfully primed your new coil, another crucial step in preventing vape coils from burning is maintaining proper saturation throughout their use. Saturating coils with e-liquid ensures continuous flow to keep them cool and prevent dry hits.

To keep your coils properly saturated, it’s essential to monitor your e-liquid levels in the tank. As you vape, make sure not to let your tank run completely empty as this can lead to insufficient liquid reaching the coils. Remember to top up your tank regularly to keep the wicking holes submerged in e-liquid.

Additionally, it’s important to choose an e-liquid with an appropriate VG/PG ratio for the coil type you are using. High VG e-liquids (thicker liquids) require low resistance coils for better absorption, while high resistance coils used for mouth-to-lung (MTL) vaping work best with thinner liquids containing less VG.

Using the correct e-liquid consistency ensures that the coils receive proper saturation, reducing the likelihood of burning.

Tip: Maintaining a topped-up tank and choosing the right e-liquid ratio for your coil can go a long way in preventing dry hits and premature coil burning.

By ensuring the coils remain saturated with e-liquid and adjusting the consistency of your liquid to match the coil type, you can prolong their lifespan and enjoy a smoother vaping experience overall.

Perfecting Your Inhaling Technique

When it comes to preventing vape coils from burning, perfecting your inhaling technique is key. Why is this important? 

Well, improper inhalation can draw too much liquid out of the coil, leading to dry hits and potentially burning the coil. To avoid this, it’s crucial to adjust your inhalation based on your vaping style.

For those who prefer mouth-to-lung (MTL) vaping, taking longer, gentle draws is recommended. This allows the coil to heat the e-liquid gradually without overwhelming it. On the other hand, direct-to-lung (DL) vapers should inhale more forcefully and directly into their lungs.

Different Styles of Vaping

When it comes to vaping, there are two primary styles: mouth-to-lung (MTL) and direct-to-lung (DL). Understanding these styles is essential in preventing vape coils from burning and optimizing your overall vaping experience.

Mouth-to-lung (MTL): This style closely mimics the act of smoking a traditional cigarette. When using an MTL setup, the vapor is first drawn into the mouth before being inhaled into the lungs. MTL vaping requires higher resistance coils and typically uses thinner e-liquids with less vegetable glycerin (VG) content.

Direct-to-lung (DL): With DL vaping, the vapor is inhaled directly into the lungs without holding it in the mouth first. DL setups often have lower resistance coils and are designed for generating larger clouds of vapor. High VG e-liquids are commonly used with DL vaping due to their thicker consistency and ability to produce denser vapor.

It’s important to note that each style requires specific coil types and e-liquid ratios for optimal performance. Using the wrong coil or e-liquid can result in dry hits, burnt coils, and a subpar vaping experience.

Optimizing Power Settings

One of the key factors in preventing vape coils from burning is optimizing power settings. Understanding the wattage range recommended for your specific coil and adjusting it accordingly can greatly extend the lifespan of your coils. Wattage is a measurement of the electrical power your vape operates at, determining the temperature to which the e-liquid is heated. Different wattages offer varying vaping experiences, including flavor, throat hit, vapor production, and inhale smoothness.

When you set your wattage too low for a sub-ohm coil, for example, you may experience insufficient vapor production or a lack of flavor. On the other hand, setting it too high can lead to burnt hits and a shortened coil lifespan. So, finding that sweet spot where flavor and vapor production are balanced while avoiding burnt coils is crucial.

Let’s say you have a Drag Q Kit by VooPoo with a recommended wattage range of 8-25W. Starting at the lower end and gradually increasing the wattage until you find your preferred balance of flavor and vapor can help optimize your power settings and prevent coil burning.

It’s important to note that recommended wattages may vary depending on the specific product and coil used.

Remember, finding the right power settings is not a one-size-fits-all approach. Experimentation and understanding your own preferences will play a significant role in optimizing your vaping experience while avoiding burnt coils.

Using Smart Features

To further enhance your vaping experience and prevent coil burning, many modern devices are equipped with smart features that can assist you in achieving optimal performance.

These features aim to regulate wattage, prevent overheating, and provide additional safeguards against burnt coils.

For instance, some vape devices offer temperature control modes that allow you to set an exact temperature at which your coil operates, ensuring it never exceeds its safe temperature threshold. This can significantly reduce the risk of burning your coils and also help prevent dry hits.

Additionally, certain devices incorporate advanced chipsets that monitor various factors such as coil resistance, puff duration, and battery voltage. These intelligent systems can automatically adjust wattage output to provide a consistent vaping experience while keeping your coils protected.

The Xros Mini Kit by Vaporesso, for example, has an 11-16W power output suitable for strong nicotine salts and 50/50 vape juices. It also offers compatibility with sub-ohm vaping using the Xros 0.8 Ohm Mesh Pod.

The device’s smart detection feature recognizes which pod is inserted and adjusts the wattage accordingly to prevent coil burning and ensure optimal performance.

By utilizing these smart features, you can benefit from the device’s built-in intelligence to take care of your coils and enjoy a hassle-free vaping experience.

Ensuring Effective Absorption of E-Liquids

When it comes to preventing vape coils from burning, one crucial factor to consider is ensuring the effective absorption of e-liquids by the coil. Proper absorption ensures that the coil remains sufficiently saturated, preventing dry hits and potential burning.

One helpful tip for ensuring effective absorption is to prime the coil correctly before turning on the device.

This involves applying drops of e-liquid to each hole on the side of the coil until it’s saturated. By doing so, you allow the coil to fully prime and soak up the e-liquid, creating an optimal environment for vaping.

Imagine this process as preparing a sponge before using it to clean. If you don’t dampen the sponge thoroughly, it won’t efficiently absorb water or do its job effectively.

Another crucial aspect is choosing the right e-liquid with an appropriate VG/PG ratio for your specific coil type. High VG e-liquids are thicker and require low resistance coils for proper absorption, while high resistance coils for mouth-to-lung (MTL) vaping need thinner liquids with less VG.

By matching the e-liquid viscosity with the coil’s compatibility, you optimize absorption and reduce the risk of burning.

Furthermore, keeping the tank topped up with e-liquid is essential in maintaining effective absorption.

This ensures that the wicking holes in the coil remain submerged and continuously supply e-liquid to prevent dry hits. Regularly checking and refilling your tank helps maintain a consistent and satisfying vaping experience without running into issues caused by insufficient liquid.

Think of it like driving a car – you need to keep an eye on your fuel gauge and refill when necessary to avoid running out of gas midway through your journey.

By following these tips and techniques for effective absorption of e-liquids, you can significantly reduce the chances of vape coils burning prematurely.

It’s important to note that finding a balance between sufficient absorption and not over-saturating the coil is crucial. Experiment with different techniques and observe how your device performs to achieve the optimal vaping experience.